Electric resistance furnaces, heat treatment furnaces, electric arc furnaces, and intermediate frequency furnaces, and cooling and assembly lines use inverters such as pumps and motors as non-linear load devices, which inevitably bring about harmonics and cause many adverse production effects. For example, capacitance oscillation is caused to make the capacitance compensator (capacity 1.1MVar) trip, which means it cannot be put into use. Affecting the heating process, the heating performance of the heat treatment device can not reach the expected effect, and the heating speed can be extended by several times; The measurement and control equipment was damaged many times for no reason; it affected the safe operation of the transformer and caused a great potential safety hazard.
Introduction
The active power filter (APF) is mainly composed of controller, isolation switch (circuit breaker), contactor, IGBT, driving circuit, protection system, fuse, connection reactor, DC capacitor, etc. The controller measures phase A, C reactive power(current), produces control signal, drives IGBT on/off and produces harmonic and reactive current same as system harmonic current but in opposite phase to filter system harmonic, reduce reactive power and keep system power factor approximately at 1.
Our APF equipment is module structure,there are two types Wall Mounted and cabient mounted.The Wall Mounted type is preferred to be used in equipment improvement which is very conveninet to install.
The Sanhe Modular Active Harmonic Filter series are suitable for applications of all types, providing harmonic mitigation, load balancing and step-less reactive power compensation for inductive and capacitor loads.
Main Parameter
Rated voltage: 0.4kV,0.69kV
Frequency: 45Hz ~ 63Hz
Three level topology and high efficiency up to 97%
Filtering capacity: THDi (current distortion rate) < 5%
Response time: less than 15ms
Communication interface: RS485, network port,Wi-Fi
Feature
Harmonic, dynamic reactive power and imbalance compensation mode available.
Compact and reasonable structure, flexible installation.
Combination of FFT and instantaneous power algorithm available.
3DSP+CPLD control mode
2nd ~50th harmonic can be compensated simultaneously, and specific harmonic orders are programmable.
Harmonic compensation, reactive power compensation and three-phase unbalance compensation.
Communication protocol: the power of the general protocol, Modbus protocol, TCP/IP
Fault alarm and recording function, can be as much as 500 alarm records.
With all kinds of complete and effective protection measures, such as over-voltage protection, under voltage protection, short circuit protection, inverter bridge reverse protection, compensation protection etc.
Protection grade: IP20, the remaining IP grade can be customized
Human-friendly LCD displaying all voltage, current and harmonic data in numerical, waveform and spectrum. Log record is available.
Specification Sheet
| Model |
Output
Current
(A) |
Electrical
Wiring |
Net Weight(kg) |
Structure |
| APFM0.4-35/3(4)a |
35 |
3 phase,3 wires/3 phase,4 wires |
32 |
Wall Mounted
|
| APFM0.4-50/3(4)a |
50 |
3 phase,3 wires/3 phase,4 wires |
32 |
| APFM0.4-60/3(4)a |
60 |
3 phase,3 wires/3 phase,4 wires |
40 |
| APFM0.4-100/3(4)a |
100 |
3 phase,3 wires/3 phase,4 wires |
45 |
| APFM0.4-150/3(4)a |
150 |
3 phase,3 wires/3 phase,4 wires |
48 |
| APFM0.4-35/3(4)b |
35 |
3 phase,3 wires/3 phase,4 wires |
32 |
Rack Type |
| APFM0.4-50/3(4)b |
50 |
3 phase,3 wires/3 phase,4 wires |
32 |
| APFM0.4-60/3(4)b |
60 |
3 phase,3 wires/3 phase,4 wires |
40 |
| APFM0.4-100/3(4)b |
100 |
3 phase,3 wires/3 phase,4 wires |
45 |
| APFM0.4-150/3(4)b |
150 |
3 phase,3 wires/3 phase,4 wires |
48 |
Advantages:
Optimize your harmonic filtering efficiency: the 3-Level Topology Design Approach
Active harmonic filters are based on power electronic technology, designed for mitigating harmonics injected by non-linear loads in power networks, generally installed in parallel to the polluting loads. The active filters analyze the line current harmonics drawn by the loads and generate a compensation current at the opposite phase angle, thereby "neutralizing" the harmonic currents.
Optimized harmonics filtering efficiency
Selection of every harmonic to the 50th order /Filter up to 50th harmonics simultaneously /Harmonic filtering levels [%] for each specific harmonic order can be pre-configured / Resonance protection by means of pre-configuring harmonic filtering levels for the potential resonance zones / Harmonic attenuation > 97%
Compact high performance
Ultra-compact, space economical / User-friendly, ease of commissioning / Parallel capability of modular AHF units with respect to network requirements / Available in rack, wall mounting designs and complete enclosure type
Enhanced Reliability Levels
Incorporates intelligent FFT calculation method:
Provides "real time sensing" of network impedance for progressive harmonics compensation to achieving system stability
Advanced control algorithm for resonance protection
In event of parallel resonance with load variations, the APF is designed to assess and "shut-down" to avoid equipment damage
Unique modular design.
Each module works independently both in wall and rack mount type, easy for logistics, installation and maintenance work.
Modular power ratings 35A/50A/60A/100A, and unlimited combination in parallel.
The maximum capacity per cabinet can be 600A, especially used in applications where space is at a premium.
Audited Supplier 
){kind=link}