| Customization: | Available |
|---|---|
| Type: | High Voltage Capacitor |
| Application: | General Purpose, Power, High Voltage |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
Introduction:
Surge capacitor is also called protective capacitor,widely being used to restrain switching overvoltage and atmosphere overvoltage. Usually, it is connected with a high voltage resistor in series to combine a RC absorb device.It can absorb the switching overvoltage caused by switching of vacuum switch.
A surge capacitor, also known as a surge suppressor or surge protector capacitor, is an electrical component used to protect electronic devices and electrical equipment from voltage spikes or transient overvoltage.
Feature:
All-film low loss dielectric
Non-PCB insulating fluid
Fitted with internal discharge resistors
Hermetically sealed unit
High grade stainless steel enclosure
Applications:
Used in the application which has voltage spikes or transient overvoltage etc.
Motors and generators
Installations with vacuum switching devices
Transformers
MV switchgear and motor control centers
Usage condition
Ambient temperature:-40-+40C
Relative humidity :less than 95%.
Altitude : less than 1000m( customization acceptable)
Environment: no corrosive gas,steam or heavy dust and no violent vibration.( customization acceptable)
Technical Parameter
|
Rated Frequency |
50/60Hz |
|
Rated Voltage |
6.6/√3,11/√3,24/√3,35/√3,40.5/√3,115/√3 etc |
|
Tangent loss angle (%) |
≤0.05(customization ≤0.001) |
|
Capacity tolerance |
-10%~+10% |
|
Electric medium |
Polypropylene full film |
|
Impregnant |
not contain chlorinated biphenyls, environmentally friendly and non-toxic |
|
Insulation Level(BIL)kV |
75,110,150 |
|
Pole type |
3 or 1 |
|
Allow long-term operation under 1.2 times rated voltage |
|
|
Allow continuous operation at 1.3 times the rated current of steady state overcurrent caused by overvoltage,harmonics and capacitance deviation. |
|
Model Selection
When the surge capacitor works as over-voltage absorbing device of RC in series,it is commonly with the high-voltage resistor of not less than 200W and 100Ω. The resistors can be fixed in the top of capacitor's bushings,but not standing the mechanical stress.
Note:If you could not decide the model selection,please feel free to contact us.
We accept OEM business. If you have requirement for your new build panels, we can give a good price.
If it is retrofit project,please advise the original capacitor name plate, drawing and the reason of replacement. Such, we can recommend you replacement solution.
Standard:
GB/T11024.1- 2019 (IEC 60871-1:2014 MOD)
FAQ
Why do we use surge capacitors?
These power quality problems like voltage spikes or surges, which can occur due to lightning strikes, power grid fluctuations, or other electrical disturbances are can be protected by Sanhe surge capacitors.
How does surge capacitor protect loads?
The surge capacitor works by absorbing and dissipating the excess energy from the transient voltage spikes, diverting it away from the connected devices. It can act as a temporary storage for the excessive electrical energy and then release it slowly to the ground or back into the electrical system. This helps to maintain a more stable voltage level and prevent it from reaching dangerous levels that could damage the equipment.
Simulation of GRID Reactive Load Flow
Analysis of L-C Circuit Amplitude-frequency Characteristic
Integration & Relay Coordination Reaction
Characteristic Curve of Permanent Magnet Breaker
Sampling & Filtering of Electronic Circuit
IGBT Driving & Protection
PWM Technology
Technology about Semiconductor Forced Commutation
Thermal Simulation & Heat Exchange Design
Feed-forward Second-order Complex Vector Algorithm
3D & Data Simulation
Instrumented IOT Communication
VP Scheduling & Dispatcher
Digital Twins of Micro-Grid & Islanding-Grid
Sanhe has specialized in over 20 years experience in power quality products and solution. We have met most of power quality problems and gave the solutions.
What kind of technical service does Sanhe provide?
• Project-site power quality test ( or test report from customer)
• Improvement solution and budget
• Product solution and price
• Products supply
• Product commissioning
What kinds of standards does Sanhe product conform to?
Except China standards, Sanhe products also conform to IEC standards including
IEC61921 :2003 IEC61000-4-5:2005
IEC60529:2001 IEC60931-1: 1996
IEC60439-1 :2005 IEC60664-1 2007
IEC60831-1: 1996 IEC61000-4-3/2/4/5/18 IEC61000-2-4
IEC60255 IEC62208 2011…
IEC255-22-1
What is the compensation effect after using Sanhe products?
• Harmonic filtering meets standard
• Power factor is over 0.95,electrical bill saving,low reactive power penalty killing
• Reducing the loss of transformer and line
improve the distribution ability,
prolong the lifespan of electrical equipment
How long is the product guarantee time?
Usually,the guarantee time is one year. However,we can accept over 5 years too. Please contact our sales to get details information.
How to become the distributor or agent of Sanhe brand products?
Sanhe is looking for overseas distributor and agent. If you are interested in it, please feel free to contact us.
){kind=link}